Academy › Workshop › #02
Workshop #02

Sanding 3D prints: the grits and primer that hide layer lines

Layer lines show up most on gentle slopes, not on vertical walls. Sanding and filler primer make them disappear. At 0.2 mm layers, a 15° slope has steps about 0.19 mm deep (97% of a layer); a 45° slope about 0.14 mm.

What you'll learn

  • Coarse to fine: 120, 220, 400
  • Sand slow and wet
  • Filler primer, sand, repeat

Chapters

  1. 0:00The problem
  2. 0:16Where the steps hide
  3. 1:08Coarse to fine
  4. 1:54Leave plastic to sand
  5. 2:07Priming
  6. 2:29Recap

Pause and guess

Where are the layer steps deepest? (tap to see the answer)
  1. The vertical wall
  2. The 45° slope
  3. The gentle 15° slope

Print settings

MaterialPLA
Nozzle0.4 mm
PlateSmooth or textured PEI
Print timeabout 1–2 h
Quality
Layer height0.20 mm
Strength
Wall loopskey setting3
Top shell layerskey setting5
Sparse infill density15 %
Support
Enable supportOff

Grouped by the tabs in Bambu Studio. Names differ slightly in PrusaSlicer and Cura. Settings not listed can stay at your printer profile.

Test it yourself

Print the sampler flat, as it comes. Tape off one half at the groove, sand the other half from coarse to fine, wet, then give the whole part one thin coat of filler primer. Hold it under a lamp: on the gentle slope, the taped half still shows every step, the sanded half should not.

Mentioned in this episode

Full transcript

Your print looks great, until you hold it under a lamp. Every single layer line shows. Today: sanding and priming, the step that makes a print look moulded.

And paint won't hide them. Glossy paint can even make them stand out more. So you grab sandpaper, go at it hard, and the plastic turns fuzzy and gummy.

Meet this episode's free model: a sanding sampler. A vertical wall at the front, a 45 degree slope, and a gentle 15 degree slope. Same layers everywhere.

Pause and guess. Where are the layer steps deepest? A: the vertical wall. B: the 45 degree slope. Or C: the gentle 15 degree slope?

It's C, the gentle slope. The flatter the slope, the deeper the steps. That surprises most people.

Every layer is a stair step. On the 15 degree slope, each step is about 0.75 millimeters wide and 0.19 deep. That's 97 percent of a full layer. At 45 degrees, it's 0.14. The vertical wall has no stairs at all, just the round edges of each line.

Thinner layers make smaller steps, like we worked out in Print Math number one. But they cost time. Sanding is how you finish the job.

The number on sandpaper is the grit. Higher means finer. P120 grains are about an eighth of a millimeter. P400, about a thirtieth. Each step roughly halves the grain size.

Start around P120, only until the ridges are gone. Then P220, then P400. Each grit just removes the scratches of the one before. Skip one, and the deep scratches stay.

And go slow. PLA starts to soften around 60 degrees Celsius. Fast sanding or a power sander heats it up, and it smears instead of sanding. Wet sanding helps: the water keeps it cool, the paper clogs less, and the dust stays down.

Tape off one half at the groove and sand the other, so you can compare. Use a block on flat faces. A bare finger pushes the paper into the valleys and rounds your edges.

Sanding takes plastic away, so leave some to spare. In your slicer, go from 2 wall loops to 3. That's 1.26 millimeters instead of 0.84, and keep 5 top layers. Names differ per slicer.

Sanding leaves the deepest valleys and fine scratches. That's what filler primer is for: a thick, sandable primer. Spray a few thin coats, and let each one dry as the can says. Deep gaps need putty first.

Here's the trick: primer is a flaw detector. One flat grey shows every scratch you missed. Sand the primer wet with P400 or finer, and prime again where you need to.

In short: sand coarse to fine, from 120 to 220 to 400. Go slow and wet, so PLA stays cool. Then filler primer, sand, and repeat.

The sanding sampler is free to download. Tape off one half, sand the other, and tell me in the comments: which grit did you stop at? Next time in the Workshop: painting it. Subscribe so you catch it. I'm Spoolbert, see you in the next one.

Spoolbert

Spoolbert explains one 3D printing problem per episode, with a free model to test the fix. Made by EMBODY³, a 3D printing studio in Belgium.

Follow Spoolbert for the next fixYouTubeTikTokInstagramFacebook