Bigger nozzle, slower print? Max volumetric speed explained
You swapped a 0.4 nozzle for a 0.8 to print faster, and the print got slower. Why? Your hotend melts only so many mm³ per second, the filament profile caps it (max volumetric speed), and a 0.8 at 0.4 mm layers needs almost four times the plastic per millimetre. Plus: how to see the cap in the preview, and why 0.6 is the sweet spot.
What you'll learn
- The limit is plastic per second
- Big nozzle: slow lines, thick walls
- Check the flow preview, try 0.6
Chapters
- 0:00The question
- 0:21Plastic per millimetre
- 0:34The melt limit
- 1:12The speed cap
- 1:46Why it got slower
- 1:57See it in the preview
- 2:22The sweet spot
- 3:11Recap
Pause and guess
Limit 20 mm³/s. How fast can a 0.8 line go? (tap to see the answer)
- About 70 mm/s
- About 140 mm/s
- About 270 mm/s
Print settings
| Quality | |
|---|---|
| Layer height | half the nozzle (0.20 / 0.30 / 0.40 mm) |
| Strength | |
| Wall loopskey setting | 2 on a 0.4 (1 on a 0.8 gives about the same wall) |
| Top shell layers | 4 on a 0.4 (2 on a 0.8 gives the same skin) |
| Sparse infill density | 15 % |
| Support | |
| Enable support | Off |
| Others | |
| Max volumetric speed (filament settings)key setting | Filament settings → keep your profile's value (check it after a nozzle swap) |
Grouped by the tabs in Bambu Studio. Names differ slightly in PrusaSlicer and Cura. Settings not listed can stay at your printer profile.
Test it yourself
Full transcript
You swapped your 0.4 nozzle for a 0.8 to print faster. And the print got slower. Today: why a bigger nozzle isn't faster, how to see it in your slicer, and the size that does speed you up.
Sound familiar? The estimate went up, and in the preview the lines crawl along, around 70 millimetres per second with a typical PLA limit. Where did the speed go?
A 0.8 at 0.4 millimetre layers lays a line about twice as wide as a 0.4 line, and twice as tall. Twice times twice: almost four times the plastic for every millimetre.
All that plastic has to melt, and filament needs time in the hot zone. Push faster, and the core stays solid, pressure builds, the extruder skips, and too little plastic comes out: thin walls with gaps. So every hotend melts only so many cubic millimetres per second.
Your slicer knows that limit. It's called max volumetric speed, and it sits in the filament profile, not with the nozzle. Some slicers load a separate filament preset per nozzle size, so check the value after a swap. Here: 20, as an example.
Set it higher than your hotend can melt, and those gaps come back. A bigger nozzle mostly gives a bigger hole. The melting happens above it, in the same hotend.
Pause and guess. With a limit of 20 cubic millimetres per second, how fast can a 0.8 line go? A: about 70 millimetres per second. B: about 140. Or C: about 270?
It's A: about 70. The same limit lets a 0.4 line run at about 270.
Same plastic per second, four times the plastic per millimetre, so the head moves about four times slower. A bigger nozzle barely melts more. It mostly spreads the same plastic thicker.
Why slower, not equal? Keep 2 walls and 4 top layers, and the 0.8's walls come out almost twice as thick, its top skin twice as thick. More plastic, same limit: more time.
See it before you print. In the preview, switch the colour scheme to volumetric flow. If most of the part sits at the top of the legend, at your filament's limit, you're capped. More speed changes nothing. Blue and green mean room to spare.
The free test block shows both. The solid tower has big layers and long lines: there you hit the limit. The four thin pegs are small round loops: most slicers print small perimeters slower, so the limit barely matters there.
And short lines are where a 0.6 wins. With an example acceleration, a 0.4 needs about 3.5 millimetres to reach 270. On a 10 millimetre line it averages only about 12 of its 20. A 0.6 is up to speed in under a millimetre, and averages about 17.
That's why 0.6 is the sweet spot: about 2.2 times the plastic of a 0.4, at a calm 120 millimetres per second. A 0.8 squeezes out only a little more, about 19, and its thick lines cost you detail: small text, holes and fine edges.
What to check first? Open the volumetric flow preview. Capped? Then match the thickness, not the count: one 0.8 wall is about as thick as two 0.4 walls, so you can often drop one, and half the top layers give the same skin. Faster still needs a hotend upgrade, not a nozzle swap.
In short: the limit is plastic per second, set in your filament. A big nozzle means slow lines and thick walls. Check the flow preview, and try a 0.6.
Tell me in the comments: which nozzle is on your printer, and did a bigger one ever print slower for you? Next time in You Asked: line width versus wall thickness, and why thin parts over-extrude. Subscribe so you catch it. I'm Spoolbert, see you in the next one.

Spoolbert explains one 3D printing problem per episode, with a free model to test the fix. Made by EMBODY³, a 3D printing studio in Belgium.